FPV and Building

Betaflight vs iNav: Which Flight Controller Firmware to Use

Betaflight or iNav? Compare acro feel, GPS Rescue, position hold and waypoint missions, and find which firmware suits freestyle, racing or long range.

On this page
  1. What they have in common
  2. Betaflight: built for acro
  3. iNav: built for navigation
  4. Hardware and versions
  5. Which to use
  6. Common mistakes
  7. Test your return-to-home

Betaflight and iNav are both flight controller firmware. They share a lot of history and tools, but they are built for different jobs. In short: use Betaflight for acro FPV on 3–5 inch freestyle and racing quads, whoops and cinewhoops. Use iNav for GPS navigation, long-range multirotors, and fixed-wing or VTOL aircraft.

What they have in common

Both descend from Cleanflight, which came from Baseflight and MultiWii. They share a similar configurator, a command-line interface (CLI), the MSP protocol and Blackbox logging. Settings are not interchangeable, though, so you cannot copy a Betaflight configuration into iNav.

Betaflight: built for acro

Betaflight is built for crisp, predictable acro flying in freestyle, racing and cinewhoops. Its main features include:

  • RPM filtering, which needs bidirectional DShot to read motor speed.
  • Dynamic notch filters and feedforward, which help with control and smoothness.
  • GPS Rescue, an emergency return to the launch point. It climbs, flies back, and descends. It waits for a minimum number of satellites (8 by default).

GPS Rescue is a failsafe, not a navigation system. It does not hold position or follow waypoints.

iNav: built for navigation

iNav is built around navigation and GPS-assisted flight:

On a multirotor, iNav’s navigation needs GPS. A compass and a barometer are recommended. Check the current iNav documentation before you buy a board for a compass-less setup, since support changes between versions. iNav’s flight feel is tuned for smooth cruising, so it is less crisp than Betaflight in freestyle.

iNav major versions arrive roughly once a year, and settings often do not carry over from one major version to the next.

Hardware and versions

Both run on STM32 F4, F7 and H7 flight controllers. Some low-flash F411 boards are not supported by recent iNav versions, so check the board list before you buy. Betaflight has moved its configurator to a web-based app, and its version naming changed in 2025. Check the current release notes, because both firmwares change quickly.

Which to use

Build Firmware Why
3–5 inch freestyle Betaflight Crisp acro feel and RPM filtering
Racing quad Betaflight Low latency, no navigation needed
Tiny whoop or cinewhoop Betaflight Acro flying, often indoors
7 inch and up, long range iNav Position hold and RTH
Fixed-wing FPV iNav Fixed-wing support
Autonomous mapping ArduPilot or PX4 More autonomy, heavier to set up

ArduPilot and PX4 are full autonomy options for survey work. They take longer to set up than either firmware here.

Common mistakes

  • “GPS Rescue is a full RTH.” It is an emergency failsafe. It is not a full navigation system.
  • “iNav flies acro worse.” It is tuned differently. Betaflight leads for crisp freestyle feel.
  • “You can paste a Betaflight diff into iNav.” The CLI settings are not compatible.
  • “Firmware fixes bad hardware.” Vibration and build quality cause many flight problems, and firmware cannot fix them.

Test your return-to-home

Test RTH or GPS Rescue at a safe altitude, in an open area, before you rely on it. What to do if your drone loses signal covers what happens when it triggers. Keep the props off while you flash and configure the board. How to build a drone covers the setup steps, and the ESC guide explains the DShot settings that RPM filtering needs.

The complete guide to fpv and building

FPV Drones: A Beginner's Guide
Read the guide

Keep exploring

Guides from other topics

All topics →